Menu
Exam Questions

Edexcel GCSE Computer Science (1CP2) Exam Questions

Build a practice paper from 514 exam-style questions, each with its mark scheme and example answers. Print it, or answer it on paper and then open the mark schemes. Or browse the questions by topic.

Build a paper

Topics (none ticked: all of them)
Question types (none ticked: all of them)

Practice paper

2 questions · 3 marks

Pick again
Print
1Short recall1 markCharacter Sets Swap Remove

A computer can store a maximum of 80 bits for a text message. Each character is stored using 7-bit ASCII.

State the maximum number of whole characters that can be stored in the message.

[1 mark]
Mark scheme

Award one mark for:

  • 11 (characters) (1)

Allow 11 remainder 3.

Allow 80 ÷ 7 = 11.428... rounded down to 11.

Do not accept 11.4 or 12 (rounding up or giving a decimal answer).

Do not award an unevaluated calculation such as 80 ÷ 7 with no answer.

Example answers and how they were marked
Full marks1/1

11

Why: Correct: 80 ÷ 7 = 11 remainder 3, so 11 whole characters can be stored (1).

No marks0/1

11.4

Why: Near miss: gives a decimal result rather than the number of whole characters; the mark scheme does not accept 11.4.

No marks0/1

12

Why: Rounds up to 12, but 12 characters would need 84 bits, more than the 80 available; the mark scheme does not accept 12.

2Describe2 marksLow and High Level Languages Swap Remove

A device driver is software that allows the operating system to control a piece of hardware. Device drivers are often written in a low-level programming language.

Describe one reason why a low-level programming language is suitable for writing a device driver.

[2 marks]
Mark scheme

Award up to two marks for a linked description such as:

  • Instructions can manipulate/control the hardware/memory/registers directly (1) so the driver can control the specific device it is written for (1)
  • The code is written for one specific processor/architecture (1) so it works with the exact hardware it will control (1)
  • The programmer controls exactly how memory/registers are used (1) so the code is efficient and needs little memory, which suits a device that has limited memory (1)
  • Each instruction maps to one machine code instruction (1) so the driver code is small enough to fit in the memory of the device (1)

Extra detail, such as naming the device the driver controls, is not needed to earn the marks.

Do not accept 'it is closer to machine code' on its own: it must be developed to show how this helps the driver, e.g. it can control the hardware directly.

Do not accept 'it is faster/quicker' with no link to the hardware/device, e.g. the device responds quickly.

Do not accept 'it is easier to learn', 'it is easier to debug' or 'it takes less time to write'.

Example answers and how they were marked
Full marks2/2

Low-level instructions can manipulate the hardware and memory directly (1) so the driver can control the specific device it was written for, such as a sound card (1).

Why: Point about direct control of hardware/memory (1) linked to controlling the specific device (1). The named device is extra detail and is not needed.

Some marks1/2

Low-level instructions can manipulate the hardware directly.

Why: Correct point (1) but no linked development saying how this helps the device driver.

No marks0/2

It is closer to machine code so it runs faster than a high-level language.

Why: 'Closer to machine code' is not developed into how this helps the driver, and 'runs faster' is not linked to the hardware/device, so no mark.

Questions by topic

2.1 Binary

Build a paper on this topic 58
Adding Binary Numbers 6 questions Binary and Hexadecimal Basics 10 questions Binary Shifts 6 questions Binary to Denary Conversion 6 questions Binary to Hexadecimal Conversion 6 questions Denary to Binary Conversion 6 questions Denary to Hexadecimal Conversion 6 questions Denary to Negative Binary Conversion 6 questions Hexadecimal to Binary Conversion 6 questions

2.2 Data representation

Build a paper on this topic 56
Character Sets 18 questions Images 19 questions Sound 19 questions

2.3 Data storage and compression

Build a paper on this topic 24
Compression 18 questions Units & Conversion 6 questions

3.1 Hardware

Build a paper on this topic 77
Embedded Systems 17 questions Fetch Decode Execute Cycle 15 questions Primary Memory 15 questions Secondary Memory 15 questions Stored Program Computers 15 questions

3.2 Software

Build a paper on this topic 124
File Management 18 questions Memory Management 16 questions Peripheral Management 11 questions Process Management 12 questions Purpose & Function of Operating Systems 17 questions Software Basics 13 questions User Management 18 questions Utility Software 19 questions

3.3 Programming languages

Build a paper on this topic 37
Low and High Level Languages 19 questions Translators 18 questions

4.1 Networks

Build a paper on this topic 138
Addressing 16 questions LANs & WANs 16 questions Network Speed 5 questions Packet Switching 16 questions Protocols & Layers 17 questions The Internet 16 questions Topologies 17 questions Wired Connections 17 questions Wireless Connections 18 questions

More ways to revise Edexcel GCSE Computer Science (1CP2)

Activities Flashcards Revision notes

Teachers: build a paper, print it with the mark schemes at the end, and sign your school up to set your classes activities on every topic.

Fetch Decode Explain isn't affiliated with or endorsed by Pearson Edexcel.