Edexcel GCSE Computer Science (1CP2) Exam Questions

Award one mark for any of the following up to a maximum of two marks:

• An arithmetic operation, e.g. addition/subtraction/multiplication/division (1)
• A logical operation, e.g. comparing two values (is A > B?) / using AND, OR, NOT (1)

Do not accept decoding instructions, fetching instructions or controlling the timing of the CPU, as these are carried out by the control unit.

Award up to two marks for a linked description such as:

• Decodes each (fetched) instruction (1) to work out which operation is needed / which components should carry it out (1)
• Coordinates/directs the other components (1) by sending control signals along the control bus (1)
• Fetches the next instruction (1) by sending its address to main memory along the address bus (1)
• Sends a read/write control signal to main memory (1) so that the instruction or data is transferred during the fetch/execute stage (1)

Do not accept answers about synchronising the CPU or timing the cycles (that is the role of the clock).

Do not accept answers about carrying out arithmetic or logical operations (that is the ALU).

Do not accept answers about holding data or the results of instructions (that is registers/main memory).

Do not accept generic answers that only say the CU controls the CPU or processes instructions, with no linked development.

Only award one mark for a response that only repeats that the CU sends control signals; the second mark needs a linked outcome such as coordination, a memory read/write, or fetching an instruction.

Do not accept 'during the decode stage' as the development for the decoding point, as it restates the question.

Award up to two marks for a linked explanation such as:

• The battery lasts longer/needs charging less often (1) because embedded systems have low power consumption/use less power (1)
• It can be made small/light enough to wear on the wrist (1) because the processor, memory and input/output are combined on a single chip/microcontroller (1)
• It can carry out the step-counting function reliably (1) because it runs a single/dedicated program and cannot install other software (1)
• It has a low cost per unit (1) because it uses fewer/less powerful components than a general purpose computer (1)

For both marks, the expansion must follow/associate with the statement.

Award one mark for a valid point stated on its own, e.g. 'it is small/light enough to wear on the wrist' (1) or 'its battery lasts longer before it needs charging' (1).

Accept the same linked ideas in either order, e.g. 'it uses less power (1) so the battery lasts longer (1)'.

Do not accept 'it uses less power'/'low power' on its own as a complete explanation; it must be linked to the battery lasting longer/needing charging less often for the second mark.

Do not accept an expansion that simply restates the point, e.g. 'it is small (1) so it fits on the wrist' earns only the point mark; 'fits on the wrist' is not a linked cause and is not enough for the second mark.

Do not accept 'the battery is small' as the linked reason for low power consumption.

Do not accept responses that say other software/apps can be installed on an embedded system (0); embedded systems have a single/dedicated function and cannot install new software.

Award up to two marks for a linked explanation such as:

• The read/write head moves over the surface of the platter (1) and detects whether each area of the disk is magnetised (1)
• The platter spins/rotates (1) so the read/write head can pass over the whole surface/tracks of the disk (1)
• The pattern of magnetised and non-magnetised areas detected by the read/write head (1) is read as binary 1s and 0s (1)
• The drive head detects the direction of magnetisation of each area (1) so the data can be read as binary (1)

For both marks, the expansion must follow/associate with the statement.

Allow one mark for stating that data is read magnetically / that the read/write head detects the magnetisation of the disk without a linked reason.

Do not accept answers that describe how data is written to the disk, such as the head magnetising the platter, rather than how it is read.

Do not accept 'a laser reads the pits and lands' - this describes optical storage, not magnetic storage.