Edexcel GCSE Computer Science (1CP2) Exam Questions

Award one mark for any of the following up to a maximum of two marks:

• An arithmetic operation, e.g. addition/subtraction/multiplication/division (1)
• A logical operation, e.g. comparing two values (is A > B?) / using AND, OR, NOT (1)

Do not accept decoding instructions, fetching instructions or controlling the timing of the CPU, as these are carried out by the control unit.

Award up to two marks for a linked description such as:

• It reads/monitors the temperature/humidity/light level using sensors (1) to switch the heaters/vents/lamps/watering system on or off when the reading is outside the set range (1)
• It compares the readings from the sensors with the set values/thresholds stored in its memory (1) to decide whether the conditions need to be changed (1)
• It monitors the light level using a light sensor (1) and turns the lamps on when the light falls below the level the plants need (1)
• It monitors the soil moisture using a soil moisture sensor (1) and turns the water pump/irrigation on when the soil is too dry (1)

For the second mark, the action/response must be linked to the sensor reading given in the first point.

Allow named sensors (temperature/humidity/light/soil moisture) and named outputs (heater, fan, vent/window, lamp, irrigation/water pump).

Do not accept answers that only name a sensor or only name an output, e.g. 'it has a temperature sensor and a heater', as there is no link between the reading and the control action.

Do not accept answers where a person switches the equipment on or off, as the embedded system controls the conditions automatically.

Award up to two marks for a linked description such as:

• Decodes each (fetched) instruction (1) to work out which operation is needed / which components should carry it out (1)
• Coordinates/directs the other components (1) by sending control signals along the control bus (1)
• Fetches the next instruction (1) by sending its address to main memory along the address bus (1)
• Sends a read/write control signal to main memory (1) so that the instruction or data is transferred during the fetch/execute stage (1)

Do not accept answers about synchronising the CPU or timing the cycles (that is the role of the clock).

Do not accept answers about carrying out arithmetic or logical operations (that is the ALU).

Do not accept answers about holding data or the results of instructions (that is registers/main memory).

Do not accept generic answers that only say the CU controls the CPU or processes instructions, with no linked development.

Only award one mark for a response that only repeats that the CU sends control signals; the second mark needs a linked outcome such as coordination, a memory read/write, or fetching an instruction.

Do not accept 'during the decode stage' as the development for the decoding point, as it restates the question.

Award up to two marks for a linked explanation such as:

• Decodes/interprets/translates the instruction (1) to work out what the instruction is/what operation is required (1)
• Sends control signals to the other components (1) so that the correct component carries out the instruction (1), e.g. the ALU/main memory
• Controls the fetch of the instruction from main memory (1) because the address of the next instruction is sent via the address bus (1)
• Controls the fetch of the next instruction from main memory (1) by sending a control signal/read signal to main memory (1)

For both marks, the expansion must follow/associate with the statement.

For the decode point, 'decodes the instruction' alone gains 1 mark; a second mark needs the purpose of decoding, i.e. working out what the instruction is/what operation is required.

Do not accept 'it controls the CPU' on its own, without naming a task in the cycle.

Do not accept 'it fetches the instruction from memory' on its own, as this describes the fetch step rather than the control unit's role; credit only if linked to controlling/signalling the fetch.

Do not accept carrying out arithmetic/logical operations, as these are carried out by the ALU, or holding the address of the next instruction, as this is the program counter.

Do not accept storing the instruction in a register (e.g. MAR/MDR), as this is not the role of the control unit.