Edexcel GCSE Computer Science (1CP2) Exam Questions

Award one mark for any of the following up to a maximum of two marks:

• An arithmetic operation, e.g. addition/subtraction/multiplication/division (1)
• A logical operation, e.g. comparing two values (is A > B?) / using AND, OR, NOT (1)

Do not accept decoding instructions, fetching instructions or controlling the timing of the CPU, as these are carried out by the control unit.

Award up to two marks for a linked description such as:

• It is a computer/processor built into a larger device (1) to carry out a single dedicated task/function (1)
• It is a combination of a processor, memory and input/output in one unit (1) that controls the device it is part of (1)
• It is a computer that forms part of another device (1) so it is not used as a general purpose computer (1)

Allow 'forms part of another device' or 'inside another device' for the first mark.

Do not award the second mark for a separate fact that is not linked to the first point, e.g. 'It is built into a device and it uses little power' would earn only the first mark (1).

Do not accept 'a small computer' on its own, with no reference to being part of another device or performing a dedicated task.

Do not accept 'a computer that controls a device' on its own, with no reference to it being built into/part of a larger device or carrying out a dedicated task.

Do not accept 'it performs a single dedicated task' on its own, with no reference to it being built into/part of a larger device.

Do not accept descriptions of a general purpose computer, e.g. 'it can run many different programs' or 'new software can be installed'.

Do not accept 'it is a system that is embedded in another system' as this repeats the term in the question.

Award up to two marks for a linked description such as:

• A read/write head moves over the surface of the disk (1) to read/write data by detecting or changing the magnetic alignment of areas of the surface (1)
• The head magnetises areas of the disk surface in different directions (1) so each area represents a binary 1 or 0 (1)
• Data is stored on concentric circles called tracks (1) which are divided into sectors (1)

Allow one mark for tracks/concentric circles on their own.

For the second mark in the first two bullets, the response must refer to the magnetic alignment/charge being detected or changed, not just that the head reads/writes data.

Do not award a mark for 'it is magnetic' or 'it stores data in binary' with no description of how the data is stored.

Do not accept descriptions of optical storage (e.g. a laser, pits and lands) or solid state storage (e.g. electric charges in chips).

Award up to two marks for a linked explanation such as:

• Decodes/interprets/translates the instruction (1) to work out what the instruction is/what operation is required (1)
• Sends control signals to the other components (1) so that the correct component carries out the instruction (1), e.g. the ALU/main memory
• Controls the fetch of the instruction from main memory (1) because the address of the next instruction is sent via the address bus (1)
• Controls the fetch of the next instruction from main memory (1) by sending a control signal/read signal to main memory (1)

For both marks, the expansion must follow/associate with the statement.

For the decode point, 'decodes the instruction' alone gains 1 mark; a second mark needs the purpose of decoding, i.e. working out what the instruction is/what operation is required.

Do not accept 'it controls the CPU' on its own, without naming a task in the cycle.

Do not accept 'it fetches the instruction from memory' on its own, as this describes the fetch step rather than the control unit's role; credit only if linked to controlling/signalling the fetch.

Do not accept carrying out arithmetic/logical operations, as these are carried out by the ALU, or holding the address of the next instruction, as this is the program counter.

Do not accept storing the instruction in a register (e.g. MAR/MDR), as this is not the role of the control unit.