Edexcel GCSE Computer Science (1CP2) Exam Questions

• A To store data and programs permanently (1)
• The only correct answer is A. The correct answer is to store data and programs permanently.
• B is not correct because storing the data and instructions currently in use is the role of primary storage/RAM, which is volatile, not the role of secondary storage
• C is not correct because calculations on data are carried out by the CPU, not by secondary storage
• D is not correct because secondary storage is not directly accessible by the CPU; data must first be copied into RAM

• A Decodes instructions (1)
• The only correct answer is A. The correct answer is Decodes instructions.
• B is not correct because the arithmetic logic unit performs arithmetic operations
• C is not correct because main memory stores data and instructions
• D is not correct because registers temporarily store data being processed

Award one mark for any of the following up to a maximum of two marks:

• (Storage that is) non-volatile / keeps its data when the power is turned off (1)
• (Storage that is) used to store programs and data/files (for later use) (1)
• (Storage that is) not directly accessible by the CPU / not directly accessed by the CPU (1)

Allow both the non-volatile point and the stores programs and data point from one sentence if each idea is clearly stated, e.g. 'non-volatile storage that holds programs and data'.

Allow accessed via the CPU / must be copied into RAM before the CPU can use it for the third point.

Do not accept volatile / loses its data when the power is turned off.

Do not accept a description of primary storage, such as RAM or ROM.

Do not accept capacity.

Do not accept an example device on its own (e.g. hard disk drive).

Award up to two marks for a linked explanation such as:

• (The ECU) is more reliable/less likely to crash (1) because it only runs the one program/has a single purpose (1)
• (The ECU) cannot be affected by other software/viruses (1) because it cannot run other software/it can only run the program it was made for (1)
• (The ECU) is cheaper (1) because it has limited processing resources/less memory/simple components (1)
• (The ECU) uses less power (1) because it has limited processing resources/a simpler processor (1)
• (The ECU) is smaller (1) because it has fewer components/less memory than a general purpose computer (1)

For both marks, the expansion must follow/associate with the statement.

A suitable benefit stated on its own earns one mark.

Do not accept a description or a location given as the reason, e.g. 'because it is part of the car', 'because it is inside the engine', 'because it is embedded'.

Do not accept a description of an embedded system on its own as the benefit, e.g. 'it does one specific job' or 'it is part of the car'.

Do not accept 'it is faster'/'it has a more powerful processor' as embedded systems have limited processing resources.

Award up to two marks for a linked explanation such as:

• Decodes/interprets/translates the instruction (1) to work out what the instruction is/what operation is required (1)
• Sends control signals to the other components (1) so that the correct component carries out the instruction (1), e.g. the ALU/main memory
• Controls the fetch of the instruction from main memory (1) because the address of the next instruction is sent via the address bus (1)
• Controls the fetch of the next instruction from main memory (1) by sending a control signal/read signal to main memory (1)

For both marks, the expansion must follow/associate with the statement.

For the decode point, 'decodes the instruction' alone gains 1 mark; a second mark needs the purpose of decoding, i.e. working out what the instruction is/what operation is required.

Do not accept 'it controls the CPU' on its own, without naming a task in the cycle.

Do not accept 'it fetches the instruction from memory' on its own, as this describes the fetch step rather than the control unit's role; credit only if linked to controlling/signalling the fetch.

Do not accept carrying out arithmetic/logical operations, as these are carried out by the ALU, or holding the address of the next instruction, as this is the program counter.

Do not accept storing the instruction in a register (e.g. MAR/MDR), as this is not the role of the control unit.