Edexcel GCSE Computer Science (1CP2) Exam Questions

Award up to two marks for a linked description such as:

• A read/write head moves over the surface of the disk (1) to read/write data by detecting or changing the magnetic alignment of areas of the surface (1)
• The head magnetises areas of the disk surface in different directions (1) so each area represents a binary 1 or 0 (1)
• Data is stored on concentric circles called tracks (1) which are divided into sectors (1)

Allow one mark for tracks/concentric circles on their own.

For the second mark in the first two bullets, the response must refer to the magnetic alignment/charge being detected or changed, not just that the head reads/writes data.

Do not award a mark for 'it is magnetic' or 'it stores data in binary' with no description of how the data is stored.

Do not accept descriptions of optical storage (e.g. a laser, pits and lands) or solid state storage (e.g. electric charges in chips).

Award up to two marks for a linked description such as:

• Decodes each (fetched) instruction (1) to work out which operation is needed / which components should carry it out (1)
• Coordinates/directs the other components (1) by sending control signals along the control bus (1)
• Fetches the next instruction (1) by sending its address to main memory along the address bus (1)
• Sends a read/write control signal to main memory (1) so that the instruction or data is transferred during the fetch/execute stage (1)

Do not accept answers about synchronising the CPU or timing the cycles (that is the role of the clock).

Do not accept answers about carrying out arithmetic or logical operations (that is the ALU).

Do not accept answers about holding data or the results of instructions (that is registers/main memory).

Do not accept generic answers that only say the CU controls the CPU or processes instructions, with no linked development.

Only award one mark for a response that only repeats that the CU sends control signals; the second mark needs a linked outcome such as coordination, a memory read/write, or fetching an instruction.

Do not accept 'during the decode stage' as the development for the decoding point, as it restates the question.

Indicative content

Why secondary storage is needed

• Secondary storage is non-volatile, so it keeps the operating system, applications and students' work when the power is turned off.
• It stores programs and files that are not currently in use, so they are not lost when the computer is switched off.
• It provides a larger capacity than primary storage for files such as students' work, videos and photographs.
• It allows each computer to keep many students' files and the software the school has installed.

The difference between primary and secondary storage

• Primary storage (RAM) is volatile and directly accessible by the CPU; secondary storage is non-volatile and not directly accessible by the CPU.
• RAM holds the data and instructions currently in use; secondary storage holds data and programs long term.
• Primary storage is faster but smaller and more expensive per gigabyte; secondary storage is slower but larger and cheaper.
• The school's computers need both: RAM to run the operating system and applications, and secondary storage to keep them when the computer is switched off.

A suitable type of secondary storage for the school's computers and a reason why it is suitable

• A solid state drive (SSD) is suitable because it has no moving parts, so it is durable and quiet, and has fast read/write speeds, which helps the computers start up quickly.
• A magnetic hard disk drive (HDD) is suitable because it is cheap and offers a very large capacity, which is useful for storing many students' files.
• Either type could be used; a small SSD for the operating system and applications plus a large HDD for files would balance speed and cost.

Levels

• Level 0 (0 marks): No rewardable content.
• Level 1 (1–2 marks): Basic, independent points are made, showing elements of understanding of key concepts/principles of computer science. (AO1) The discussion will contain basic information with little linkage between points made or application to the context. (AO2)
• Level 2 (3–4 marks): Demonstrates adequate understanding of key concepts/principles of computer science. (AO1) The discussion shows some linkages and lines of reasoning with some structure and application to the context. (AO2)
• Level 3 (5–6 marks): Demonstrates comprehensive understanding of key concepts/principles of computer science to support the discussion being presented. (AO1) The discussion is well developed, with sustained lines of reasoning that are coherent and logically structured, and which clearly apply to the context. (AO2)

Additional guidance

• Award credit for a type of secondary storage only when a reason is given that is linked to the school's computers; a named type alone (e.g. 'SSD') is not creditworthy. Do not accept RAM as secondary storage or the claim that secondary storage is the same as RAM. Do not accept CD/DVD/Blu-ray as the main storage for the school's computers because their capacity is too low and write speeds are slow.
• For Level 3, the answer must cover all three bullets and apply at least one point to the school's computers. A 6-mark answer is well developed with sustained reasoning and a justified choice; a 5-mark answer covers all three but with limited development or application. Comparisons of speed and cost between primary and secondary storage are creditworthy as part of the difference.

Indicative content

What embedded systems are used for in the drone

• An embedded system is a computer built into a larger device that performs a single, dedicated function as part of that device.
• The drone contains several embedded systems, and each one is dedicated to a task such as flight control, navigation, obstacle detection or battery monitoring rather than being a general-purpose computer.
• The flight controller embedded system processes data from the drone's sensors and changes the signals sent to the rotors, so the drone stays stable and can be steered while carrying a parcel.
• The GPS receiver embedded system works out the drone's position and uses it to navigate along the route to the customer's address.
• The camera embedded system captures images or video that are processed to detect obstacles, such as trees, buildings or overhead cables, in the drone's path.
• Sensor embedded systems, for example ultrasonic or infrared sensors, measure the distance to the ground and to obstacles so the drone can land and avoid collisions.
• The battery management and communication embedded systems monitor the charge and send the drone's status and location to the control centre, and the rotor-control embedded systems drive the rotors so the drone can take off, hover and land.

Benefits of using embedded systems in the drone

• Embedded systems use little power, so the drone can fly for longer and deliver more parcels on one charge.
• They are small and light, which is important because a heavier drone needs more power to stay in the air.
• Because each embedded system is dedicated to one task, it can respond quickly and reliably, so the drone can change direction in time to avoid an obstacle.
• Combining the processor, memory and input/output in one unit reduces the number of separate components and the cost per drone, so a fleet of delivery drones is cheaper to build.
• Embedded systems allow the drone to fly autonomously, so the company does not need a human pilot for every delivery.
• Programs are held in ROM, so the drone's behaviour is consistent and predictable each time it flies.

Any drawbacks or limitations of using embedded systems in the drone

• Each embedded system has limited processing power, so the drone may not be able to run complex obstacle-recognition software and could fail to identify an unusual obstacle.
• They have limited storage and RAM, so the drone cannot store much flight data or video on board and must send it to the control centre.
• The software is held in ROM and is difficult to update, so fixing a bug or adding a new feature may mean returning the drone or connecting it to a computer.
• The embedded systems are dedicated to the drone, so they cannot easily be reused for a different task if the drone is retired.
• If an embedded system fails, the drone may crash, which could injure people or damage property, so robustness is essential.
• A general-purpose computer would be too large and heavy for the drone, so the drone has to use these limited dedicated systems and cannot run general-purpose software.

Levels

• Level 0 (0 marks): No rewardable content.
• Level 1 (1–2 marks): Basic, independent points are made, showing elements of understanding of key concepts/principles of computer science. (AO1) The discussion will contain basic information with little linkage between points made or application to the context. (AO2)
• Level 2 (3–4 marks): Demonstrates adequate understanding of key concepts/principles of computer science. (AO1) The discussion shows some linkages and lines of reasoning with some structure and application to the context. (AO2)
• Level 3 (5–6 marks): Demonstrates comprehensive understanding of key concepts/principles of computer science to support the discussion being presented. (AO1) The discussion is well developed, with sustained lines of reasoning that are coherent and logically structured, and which clearly apply to the context. (AO2)

Additional guidance

• Level 3 responses must cover what embedded systems are used for in the drone and both benefits and drawbacks/limitations, with reasoning applied to the delivery drone. Do not accept general-purpose computer uses such as connecting to Wi-Fi to play videos, installing new software, apps or games, or using a server; do not accept the drone itself as a single embedded system unless a specific dedicated function is explained.
• A definition of an embedded system on its own, with no application to the drone, cannot lift an answer above Level 1; limited storage and inability to be repurposed must be linked to the drone, for example little flight data can be stored or the system cannot be reused for another task, to gain credit.