Menu
Exam Questions

Edexcel GCSE Computer Science (1CP2) Exam Questions

Build a practice paper from 693 exam-style questions, each with its mark scheme and example answers. Print it, or answer it on paper and then open the mark schemes. Or browse the questions by topic.

Build a paper

Topics (none ticked: all of them)
Question types (none ticked: all of them)

Practice paper

4 questions · 6 marks

Pick again
Print
1Short recall1 markAddressing Swap Remove

Routers forward data packets across the internet.

State the part of a data packet that a router uses to decide where to send it.

[1 mark]
Mark scheme

Award one mark for:

  • (Destination) IP address (1)

Allow IP address on its own (the destination is implied).

Do not accept source IP address/IP address of the sender.

Do not accept MAC address.

Do not accept domain name/web address.

Example answers and how they were marked
Full marks1/1

The destination IP address.

Why: Names the destination IP address (1).

No marks0/1

The domain name.

Why: A domain name is not used by a router to route a packet; it must be translated to an IP address first, so no mark.

No marks0/1

The MAC address.

Why: A MAC address is not used to route packets across the internet; the Do not accept line applies.

2Short recall2 marksWireless Connections Swap Remove

Latency affects the performance of a network.

Define the term latency.

[2 marks]
Mark scheme

Award one mark for any of the following up to a maximum of two marks:

  • A delay/time/lag (1)
  • Between a signal/request being sent and a response/data being received (1)

Allow 'the time taken for data to travel from source to destination' for both marks.

Do not accept 'the speed at which data travels' / 'bandwidth' / 'the amount of data sent per second'.

Example answers and how they were marked
Full marks2/2

The delay between a signal being sent and a response being received.

Why: Gives the delay (1) and the time between sending and receiving (1).

Some marks1/2

The time taken for data to travel.

Why: Gives the idea of time taken (1) but does not say between sending and receiving (1).

No marks0/2

The speed at which data is sent over the network.

Why: Describes speed, not latency; no creditworthy point.

3Short recall1 markWired Connections Swap Remove

Wired connections have characteristics that affect network performance.

State what is meant by the range of a wired network connection.

[1 mark]
Mark scheme

Award one mark for:

  • The maximum distance data/a signal can be transmitted before it becomes too weak to be received (1)

Allow 'how far a signal can travel'.

Do not accept the number of devices that can be connected to the network.

Do not accept the speed at which data is transmitted.

Do not accept bandwidth/the maximum capacity of a channel.

Do not accept latency/the delay between a signal being sent and received.

Example answers and how they were marked
Full marks1/1

The maximum distance a signal can be transmitted before it becomes too weak to be received.

Why: Gives the maximum distance a signal can be transmitted before it becomes too weak, which is the creditworthy point (1).

No marks0/1

The maximum capacity of the connection.

Why: This describes bandwidth, which the mark scheme says not to accept for range, so no mark.

No marks0/1

The delay between a signal being sent and received.

Why: This describes latency/delay, which the mark scheme says not to accept for range, so no mark.

4Describe2 marksWireless Connections Swap Remove

A family uses a wireless network at home.

Describe how interference can affect the performance of a wireless network.

[2 marks]
Mark scheme

Award up to two marks for a linked description such as:

  • Other electrical/radio devices nearby (1) interfere with the wireless signal so data is corrupted (1)
  • Interference corrupts data (1) so the data has to be resent, which increases latency/slows the transfer (1)
  • Interference reduces the strength of the signal received (1) which lowers the data transfer rate the connection can support (1)
  • Interference makes the connection drop (1) so data transfer stops/devices have to reconnect (1)

Do not accept responses that only name a device (microwave, phone) without saying how it affects the network.

Do not accept responses that only state the network becomes slower without saying what causes the interference or how it affects the data.

Do not accept responses about wired connections or cables.

Example answers and how they were marked
Full marks2/2

Other electrical devices nearby can interfere with the wireless signal and corrupt data, so the data has to be resent and transfers are slower.

Why: Linked point: other electrical devices interfere and corrupt data (1), developed by the data being resent, which slows the transfer (1).

Some marks1/2

Other electrical devices nearby can interfere with the wireless signal.

Why: Cause given: other electrical devices interfere with the signal (1), but no development of how this affects the data or performance.

No marks0/2

Interference happens when the wireless cable is damaged by other cables.

Why: Misconception about cables; the mark scheme does not accept responses about wired connections or cables.

Questions by topic

2.1 Binary

Build a paper on this topic 58
Adding Binary Numbers 6 questions Binary and Hexadecimal Basics 10 questions Binary Shifts 6 questions Binary to Denary Conversion 6 questions Binary to Hexadecimal Conversion 6 questions Denary to Binary Conversion 6 questions Denary to Hexadecimal Conversion 6 questions Denary to Negative Binary Conversion 6 questions Hexadecimal to Binary Conversion 6 questions

2.2 Data representation

Build a paper on this topic 56
Character Sets 18 questions Images 19 questions Sound 19 questions

2.3 Data storage and compression

Build a paper on this topic 24
Compression 18 questions Units & Conversion 6 questions

3.1 Hardware

Build a paper on this topic 77
Embedded Systems 17 questions Fetch Decode Execute Cycle 15 questions Primary Memory 15 questions Secondary Memory 15 questions Stored Program Computers 15 questions

3.2 Software

Build a paper on this topic 124
File Management 18 questions Memory Management 16 questions Peripheral Management 11 questions Process Management 12 questions Purpose & Function of Operating Systems 17 questions Software Basics 13 questions User Management 18 questions Utility Software 19 questions

3.3 Programming languages

Build a paper on this topic 37
Low and High Level Languages 19 questions Translators 18 questions

4.1 Networks

Build a paper on this topic 138
Addressing 16 questions LANs & WANs 16 questions Network Speed 5 questions Packet Switching 16 questions Protocols & Layers 17 questions The Internet 16 questions Topologies 17 questions Wired Connections 17 questions Wireless Connections 18 questions

4.2 Network security

Build a paper on this topic 36
Network Security Risks 18 questions Preventing Network Security Risks 18 questions

5.1 Environmental

Build a paper on this topic 36
E-waste 17 questions Manufacturing Technology 19 questions

5.2 Ethical and legal

Build a paper on this topic 71
Data Protection Act 17 questions Impact of AI 18 questions Intellectual Property 18 questions Software Licences 18 questions

5.3 Cybersecurity

Build a paper on this topic 36
Malware 18 questions Social Engineering 18 questions

More ways to revise Edexcel GCSE Computer Science (1CP2)

Activities Flashcards Revision notes

Teachers: build a paper, print it with the mark schemes at the end, and sign your school up to set your classes activities on every topic.

Fetch Decode Explain isn't affiliated with or endorsed by Pearson Edexcel.