Edexcel GCSE Computer Science (1CP2) Exam Questions

Award one mark for:

• Volatile (1)

Allow volatile memory / it is volatile.

Do not accept non-volatile, ROM, RAM or temporary/short term memory on their own, as these are not the term asked for.

Award one mark for any of the following up to a maximum of two marks:

• Program instructions are stored in main memory/RAM (1)
• The data used by the program is stored in main memory/RAM (1)
• The CPU fetches/reads instructions from main memory to execute them (1)
• The program can be run without the instructions being input again (1)

Allow 'the program is stored in memory' for one mark.

Do not accept answers about programs being stored on secondary storage, such as a hard disk or USB memory stick.

Do not accept answers that only describe the von Neumann architecture (e.g. having a CPU and memory) without stating that instructions are stored in main memory.

Award up to two marks for a linked description such as:

• A read/write head moves over the surface of the disk (1) to read/write data by detecting or changing the magnetic alignment of areas of the surface (1)
• The head magnetises areas of the disk surface in different directions (1) so each area represents a binary 1 or 0 (1)
• Data is stored on concentric circles called tracks (1) which are divided into sectors (1)

Allow one mark for tracks/concentric circles on their own.

For the second mark in the first two bullets, the response must refer to the magnetic alignment/charge being detected or changed, not just that the head reads/writes data.

Do not award a mark for 'it is magnetic' or 'it stores data in binary' with no description of how the data is stored.

Do not accept descriptions of optical storage (e.g. a laser, pits and lands) or solid state storage (e.g. electric charges in chips).

Award up to two marks for a linked explanation such as:

• The address bus carries the address of the next instruction (1) so the CPU can locate/fetch it from main memory/RAM (1)
• The address bus carries the address of the memory location to be read (1) so the instruction/data stored there can be located/accessed (1)
• The CPU needs to know where the next instruction is stored (1) so the address bus sends the address to main memory/RAM (1)

For both marks, the expansion must follow/associate with the statement.

Allow 'from the program counter/PC' as part of the point for one mark, e.g. the address bus carries the address from the program counter (1), but the second mark needs the destination or purpose (e.g. to locate/fetch the instruction in main memory/RAM).

Do not award the second mark for naming the program counter/PC alone.

Do not accept answers that say the address bus carries data/instructions from main memory to the CPU, as these travel on the data bus.

Do not accept answers that say the address bus stores the address.

Do not allow an answer that only restates that the address bus carries addresses without saying which address or why it is needed.

Award up to two marks for a linked explanation such as:

• Decodes/interprets/translates the instruction (1) to work out what the instruction is/what operation is required (1)
• Sends control signals to the other components (1) so that the correct component carries out the instruction (1), e.g. the ALU/main memory
• Controls the fetch of the instruction from main memory (1) because the address of the next instruction is sent via the address bus (1)
• Controls the fetch of the next instruction from main memory (1) by sending a control signal/read signal to main memory (1)

For both marks, the expansion must follow/associate with the statement.

For the decode point, 'decodes the instruction' alone gains 1 mark; a second mark needs the purpose of decoding, i.e. working out what the instruction is/what operation is required.

Do not accept 'it controls the CPU' on its own, without naming a task in the cycle.

Do not accept 'it fetches the instruction from memory' on its own, as this describes the fetch step rather than the control unit's role; credit only if linked to controlling/signalling the fetch.

Do not accept carrying out arithmetic/logical operations, as these are carried out by the ALU, or holding the address of the next instruction, as this is the program counter.

Do not accept storing the instruction in a register (e.g. MAR/MDR), as this is not the role of the control unit.