Edexcel GCSE Computer Science (1CP2) Exam Questions

• C Main memory (RAM) (1)
• The only correct answer is C. The correct answer is main memory (RAM); accept 'main memory', 'RAM' or 'random access memory'.
• A is not correct because the arithmetic logic unit performs arithmetic and logical operations
• B is not correct because the clock sends regular pulses to synchronise the components of the CPU
• D is not correct because the program counter holds the address of the next instruction, not the instructions and data

• A Address bus (1)
• The only correct answer is A. The correct answer is address bus. Do not accept 'address' on its own.
• B is not correct because the control bus carries control signals in both directions between the CPU and other components
• C is not correct because the data bus carries data in both directions between the CPU and main memory
• D is not correct because the system bus is the collection of all three buses

Award one mark for any of the following up to a maximum of two marks:

• (Storage that is) non-volatile / keeps its data when the power is turned off (1)
• (Storage that is) used to store programs and data/files (for later use) (1)
• (Storage that is) not directly accessible by the CPU / not directly accessed by the CPU (1)

Allow both the non-volatile point and the stores programs and data point from one sentence if each idea is clearly stated, e.g. 'non-volatile storage that holds programs and data'.

Allow accessed via the CPU / must be copied into RAM before the CPU can use it for the third point.

Do not accept volatile / loses its data when the power is turned off.

Do not accept a description of primary storage, such as RAM or ROM.

Do not accept capacity.

Do not accept an example device on its own (e.g. hard disk drive).

Indicative content

The role of the CPU and registers

• The control unit decodes the instruction fetched from main memory and controls the other components during the cycle.
• The ALU carries out arithmetic and logical operations during the execute stage, such as adding two values held in registers.
• Registers hold the data, addresses and results that the CPU is working on during the cycle.
• The program counter holds the address of the next instruction to be fetched, so it is incremented after each fetch.
• The memory address register holds the address of the memory location that is about to be read or written.
• The memory data register holds the instruction or data that has been fetched from or is being written to main memory.

The role of the address bus, data bus and control bus

• The address bus carries the address of the memory location that the CPU needs to access from the CPU to main memory.
• The address bus is one-way, so addresses are only sent from the CPU to main memory.
• The data bus carries instructions and data between the CPU and main memory, so it is bi-directional.
• The width of the data bus affects how many bits can be transferred at one time.
• The control bus carries control signals such as read and write signals, so main memory knows whether the CPU wants to read an instruction or write data.
• The control bus carries signals from the control unit to coordinate the components during the fetch-decode-execute cycle.

The role of the clock

• The clock sends regular pulses that synchronise the actions of the CPU and main memory.
• Each clock pulse triggers the next step of the fetch-decode-execute cycle, so the stages happen in the correct order.
• The clock provides a regular timing signal so that the fetch-decode-execute cycle repeats at a steady rate.
• The clock is separate from the control bus; the control bus carries control signals, while the clock provides timing pulses.
• Do not credit the address bus storing addresses, the data bus storing data, or the control bus controlling the computer without naming a control signal; do not credit clock speed affecting performance as a role in the cycle.
• Level 3 responses must cover all three bullets and link them to the fetch-decode-execute cycle; Level 2 answers may identify roles but link them only partly to the cycle.

Levels

• Level 0 (0 marks): No rewardable content.
• Level 1 (1–2 marks): Basic, independent points are made, showing elements of understanding of key concepts/principles of computer science. (AO1) The discussion will contain basic information with little linkage between points made or application to the context. (AO2)
• Level 2 (3–4 marks): Demonstrates adequate understanding of key concepts/principles of computer science. (AO1) The discussion shows some linkages and lines of reasoning with some structure and application to the context. (AO2)
• Level 3 (5–6 marks): Demonstrates comprehensive understanding of key concepts/principles of computer science to support the discussion being presented. (AO1) The discussion is well developed, with sustained lines of reasoning that are coherent and logically structured, and which clearly apply to the context. (AO2)

Indicative content

Fetching and decoding an instruction

• The register that holds the address of the next instruction (the program counter) contains the address of the instruction to be fetched.
• This address is sent to main memory (RAM) and the instruction is copied from main memory into a register inside the CPU.
• The program counter is updated so that it holds the address of the next instruction in the program.
• The control unit decodes the instruction that has been fetched, working out which operation is required and which data or registers are needed.
• The control unit sends control signals to coordinate the other components as the instruction is carried out.
• The control unit decides what happens next, for example after a comparison it decides whether the next instruction is the following one or a jump.

The arithmetic logic unit (ALU) executes an instruction

• The control unit directs the arithmetic logic unit (ALU) to carry out the operation.
• The ALU performs arithmetic operations such as addition, subtraction, multiplication and division, for example adding two values in a program written by the class.
• The ALU performs logical operations such as comparing two values to see if they are equal or whether one is greater than the other.
• The result of the operation carried out by the ALU is passed back and stored in a register.
• The ALU operates on data that has been fetched from main memory; it does not fetch the instruction and it does not decide which instruction is next.

Registers

• Registers are small, very fast memory locations inside the CPU.
• They hold the data, addresses and results that the CPU is working on during the cycle.
• Registers are used in every stage of the cycle, not only when the ALU produces a result.
• Because registers are inside the CPU they can be read and written much faster than main memory during the cycle.

Levels

• Level 0 (0 marks): No rewardable content.
• Level 1 (1–2 marks): Basic, independent points are made, showing elements of understanding of key concepts/principles of computer science. (AO1) The discussion will contain basic information with little linkage between points made or application to the context. (AO2)
• Level 2 (3–4 marks): Demonstrates adequate understanding of key concepts/principles of computer science. (AO1) The discussion shows some linkages and lines of reasoning with some structure and application to the context. (AO2)
• Level 3 (5–6 marks): Demonstrates comprehensive understanding of key concepts/principles of computer science to support the discussion being presented. (AO1) The discussion is well developed, with sustained lines of reasoning that are coherent and logically structured, and which clearly apply to the context. (AO2)
• A Level 3 answer must link the roles of all three components to the fetch, decode and execute stages. An answer that links only one component to a stage, with the other points listed separately, is Level 1 (1–2 marks); an answer that links two of the components to stages is Level 2 (3–4 marks). A point repeated under more than one heading is credited once only.
• Accept 'the program counter', 'the address register' or 'a register holding the address of the next instruction' as the register that holds the address of the next instruction. Do not accept 'the control unit performs the calculations', 'the ALU controls the timing of the CPU' / 'the ALU sends the clock signal' or 'registers are in main memory (RAM)'.